The content below involving How to Install a Bathtub Yourself is amazingly entertaining. Check it out for your own benefit and see what you think of it.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily obtainable, the project can relocate quickly; if you have to open up a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will require an assistant to move out the old tub and set in the brand-new one. Make certain you have qualified on your own for the task and also are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Chances are you may need an expert plumber to make tube connections.
This short article will assist you install a new bath tub in your bathroom if you have actually currently acquired a brand-new bathtub and also do not require to alter the plan of your previous water system pipelines.
Your tools and product list need to consist of the following:
Getting ready for the Setup
Firstly, the sustaining structure provided with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather bothersome as a result of the restricted accessibility that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are handy in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water and also examine all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow outlet and the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub ought to wait up until the bathtub has been used at least when as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap as well as the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with moisture and possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack rather very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles using water-resistant or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about How to Install a Bathtub Yourself, I figured sharing that portion was essential. Remember to take the time to share this blog posting if you enjoyed reading it. Many thanks for taking the time to read it.
Information Here